Loop and Nodal Analysis and Op Amps

Loop and Nodal Analysis and Op Amps

Circuits II EE221 Unit 3 Instructor: Kevin D. Donohue Instantaneous, Average, RMS, and Apparent Power, and, Maximum Power Transfer, and Power Factors Power Definitions/Units: Work is in units of newton-meters or joules same as energy. 1 joule is work done for 1 ampere passed through 1 ohm for 1 second, or work done by a force of 1 Newton applied over 1 meter. Power is a measure of the rate at which work is done and is in units ofjoules per seconds, 746 Watts in one horsepower. Power Conversion Electric motors and generators convert electrical power to mechanical power and vise versa.

Other devices exist that convert electric power to light, heat, sound, . and vise versa Instantaneous and Average Power The instantaneous power is the power absorbed by an element at an instance of time. In an electric circuit this is given by: P (t ) v(t )i (t ) where i(t) is the current through the element and v(t) is the voltage drop over the element. Average Power over some time interval T is given by: T 1 PAV

v(t )i (t )dt T 0 If the i and v product is periodic, then PAV can be reduced to the integration over a single period. For random/non-periodic signals T goes to infinity. Instantaneous Power Instantaneous power is simply computed by the product of 2 functions. For sinusoidal problems, trig identities or phasors can be used to simplify the products and result in easier formulae for average power. Example: Write a Matlab script that plots the instantaneous power of a cosine voltage across an impedance load. Write the script so the voltage waveform and impedance can be easily changed and instantaneous power replotted. Matlab Scripts

A script is a series of Matlab command line instructions typed in a text file and stored with an *.m extension. This is referred to as an mfile. To run these commands change your current directory associated with the Matlab work space to the one containing the mfile. Then type the base name of the file in the Matlab command line. Matlab Scripts For this example comments are included in the script, and are identified by text following a % character. The functions plot and cos are used in this script. Type help plot or help cos to get a full description of these functions in the Matlab workspace. Matlab Scripts % This script will plot the instantaneous power absorbed % by an impedance load with a sinusoidal voltage over it.

% Set the parameters of the Voltage signal f = 1000; % Frequency of signal in Hz ph = 30; % Phase of signal in degrees A=2; % amplitude of signal %Set impedance value zm = 8; % Impedance magnitude zp = -40; % Impedance phase in degrees % Create a time axis of 2 periods over which to plot the power tp = 1/f; % Determine period t = 2*tp*[0:5000]/5000; % Make a 5001 point time axis (row vector) over 2 periods Matlab Scripts % Create a vector of points for voltage v = A*cos(2*pi*f*t + pi*ph/180); % Create a vector of points for the current (adjust magnitude and phase % based on impedance i = (A/zm)*cos(2*pi*f*t + pi*(ph-zp)/180); % Take an element by element product to get power p = v.*i; % Plot it plot(t,p) title(['Instantaneous Power '] )

xlabel(['Seconds']) ylabel(['Watts']) Result Instantaneous Power 0.6 0.5 0.4 Watts 0.3 0.2 0.1 0

-0.1 0 0.2 0.4 0.6 0.8 1 1.2 Seconds 1.4 1.6 1.8 2

-3 x 10 What is the meaning of negative instantaneous power? Average Power in Periodic Signals Given a sinusoidal voltage and current in a device: v(t ) Av cos(t v ) i (t ) Ai cos(t i ) Show: 1 PAV Av Ai cos( v i ) 2 Average Power in Periodic Signals Given a phasor representation of a voltage

and current in a device: V Av v I A i i Show: PAV 1 1 * Re VI Av Ai cos( v i ) 2 2

Instantaneous and Average Power Conservation of Power In a given circuit the average power absorb (denoted by positive values) equals the power delivered (denoted by negative values). For a circuit with N elements the sum of all power is zero: N 0 P i i 1 Note: These are all real or average power values. Passive Sign Convention It is assumed that positive

charge entering the positive terminal of an element implies power absorbed by the element. Therefore, charge leaving the positive terminal of an element implies power supplied or delivered by the element. If the words absorbed or supplied are not given with a power value, power absorbed will be assumed. (A negative sign will imply power supplied). I V I V Example Average Power Find the average power each of the elements given is(t) = 3cos(1000t)A 10i

a ia 25 10mH is P25=34.61W PL=PC=0 P5=21.13W PCCVS=-5.54W Pis=-50.19W 80F 5 Maximum Power Transfer Given a Thvenin circuit with load ZL: Zth Vth

ZL Show that for a maximum power transfer to the load: Z L Z th* Vth And the maximum power transfer P is: max 2 8 Re[ Z th* ] Example Maximum Power Find the impedance of the load Z to result in the maximum power transfer, and find the resulting power. Assume vs(t) = 110cos(377t) V

40F 8 vs Z=2.87-75.88 Ith=1.6583.12A Vth = 4.71159V Pz=3.98W 12 7.5mH Z Root Mean Square (RMS) Values 2 The RMS value of a 1 i

(t ) 2 PAV Ri 2 (t )dt R dt RI rms periodic current or T T T T voltage is its DC 1 2 equivalent value for I rms i (t )dt T T delivering average power to a resistor. 2 2 2 PAV

1 T v (t ) 1 dt T R R Vrms 1 T v 2 (t )dt T

V v (t ) dt rms T T R RMS Formula for Sinusoids The RMS value for a sinusoid of any frequency or phase is its amplitude divided by square root of 2. I rms I rms 1 T

A T 2 cos 2 (t )dt 2 I rms A2 T I rms A2 4T exp( j 2(t )) 2 exp(0) exp( j 2(t )) dt

I rms A2 4T A2 2dt T 4T A2 A 2T 0 4T 2 exp( j (t )) exp( j (t )) dt T 2

T exp( j 2(t )) exp( j 2(t )) dt T Apparent Power and Power Factor Apparent power (S) for sinusoidal waveforms is the product of the RMS voltage and current magnitudes without regard to their phase offsets. It is in units of VoltAmps (VA). The cosine of their phase difference is the power factor (pf). 1 1 v(t ) Av cos(t v ) i (t ) Ai cos(t i ) V Av v I A

i i PAV Re VI* Av Ai cos( v i ) Vrms I rms cos( v i ) 2 2 S Vrms I rms (apparent power) PAV S cos( v i ) (real power) Q S sin( v i ) (reactive power) pf cos( v i ) (power factor) S Vrms I rms exp j ( v i ) (complex power) Leading and Lagging The sign of phase difference between

the voltage and current is related to the angle of the impedance of the load. The terms leading and lagging are used to describe this property: v i 0 pf leading (Capacitive Load) v i 0 pf lagging (Inductive Load) v i 0 (Only Real Load)

Recently Viewed Presentations

  • Prefixes - Pacoima Charter Elementary School

    Prefixes - Pacoima Charter Elementary School

    Prefixes reading standard=1.8 Use knowledge of prefixes to determine the meaning of words. Today we are going to use prefixes to determine the meaning of words.
  • FROM THERE TO HERE AND THE FUTURE Robert

    FROM THERE TO HERE AND THE FUTURE Robert

    FROM THERE TO HERE AND THE FUTURE Robert M. White NOAA Leadership Seminar August 25, 2004 National Oceanic and Atmospheric Administration A Proud History of Service and Science Coastal Survey 1870 Weather Bureau 1871 Fisheries Commission (Bureau Commercial Fisheries) 1965...
  • Aesthetic - Marlboro Central High School

    Aesthetic - Marlboro Central High School

    Aesthetic . Adj- concerned with beauty or the appreciation of beauty. Noun- a set of principles guiding the work of an artist or artistic movement
  • Types of Plant Crops - Montgomery County Schools

    Types of Plant Crops - Montgomery County Schools

    Grain Crops include plants . grown . for their edible . seeds. but . do not include . horticultural crops. Grain crops provide many important foods including the cereal grains. Cereal grain is the seed of grass type plants grown...
  • Queries and Lookups Simple Department Form The Simple

    Queries and Lookups Simple Department Form The Simple

    Module Views Module View Looks Like Ordinary Module Module Component API Oracle Designer creates the view for you, when you tell it to. Use MCAPI. Creates DDL for the view The Underlying View The View Based Form Querying Inserting New...
  • BMES WELCOME MEETING - University of Texas at Austin

    BMES WELCOME MEETING - University of Texas at Austin

    Track 1: Skills. Image and signal processing. Analog/digital network analysis. Software/hardware programming. Circuit Design. Data acquisition. Computational analysis of data in regard to living systems
  • ISE491 Ozcan CHAPTER 12 - Mercer University

    ISE491 Ozcan CHAPTER 12 - Mercer University

    Industrial Engineering and Industrial Management ... Results in significantly better glucose and blood pressure control in those patients whose providers use it Clinical inertia is a bigger problem than patient non-compliance Fall 2019 ISE 468 ETM 568 Pursuing the Triple...
  • Foster Care Bill of Rights - Missouri Department of Social ...

    Foster Care Bill of Rights - Missouri Department of Social ...

    Any Children's Division office, residential care facility, child placing agency, or other agency involved in the care and placement of foster children shall post the foster care bill of rights in the office, facility, or agency.